Blomberg BRFB1900FBI Instrukcja Instalacji

CONFIDENTIAL ARÇELİK A.Ş. K76540NEB INSTALLATION INSTRUCTIONS

CONFIDENTIAL 9 Electrical Connection  Never use an extension cable.  The power socket must definitely be grounded and checked by an authorised p

CONFIDENTIAL 99

CONFIDENTIAL 100  Attach the Hanger Sheet (13) using 2 screws (16). Replacing the hinges  Remove the Hinge Caps located at the other side wher

CONFIDENTIAL 101  Remove the Screw caps of the hinges.

CONFIDENTIAL 102  Remove the lower right hinge by loosening its 2 screws and fix it to its slot at the upper Left side.

CONFIDENTIAL 103  Remove the upper right hinge by loosening its 2 screws and fix it to its slot at the lower Left side.

CONFIDENTIAL 104  Fix the screw caps of the hinges to their places.

CONFIDENTIAL 105  Attach the Hinge Slot Caps removed from the left side to the Hinge Caps at the right side.

CONFIDENTIAL 106 Installing the FF PU Door  Place the Fridge Inner Door to the refrigerator and fix it with 4 screws.

CONFIDENTIAL 107 Installing the Fridge Furniture Door and adjusting the door  Please see relevant chapters. INSTALLING THE DUAL CABIN If you are g

CONFIDENTIAL 108 Location of the Electrical Wiring Location of the electrical wiring must be within the range given below. ATTENTION: Do not use e

CONFIDENTIAL 10 TOOL LIST Tools to be used when installing the product are as follows: Cordless Drill Safety Goggles ½" Wrench Hammer L

CONFIDENTIAL 109 Location of the Water System The water connected to the water mains must be potable. Location of the water system must be within th

CONFIDENTIAL 110 32 - Insulation Sponge 33 - Fastener 34 - Screw

CONFIDENTIAL 111 Removing the Side Brackets  Remove the side brackets that are located in the middle of two cabinets.

CONFIDENTIAL 112 Attaching the Fasteners  Screw (34) the Fasteners (33) that are going to be used to connect two refrigerators together to the lo

CONFIDENTIAL 113  Stick the Insulation Sponge (32) to the side panel so that the sponge remains in between two cabins.

CONFIDENTIAL 114  Bring the two refrigerators side by side. After making sure that they are in alignment, screw the fasteners (33) to the other r

CONFIDENTIAL 115  Make power and water connections of the refrigerator as explained before.  Push the refrigerators into the cabin.

CONFIDENTIAL 116  Adjust the heights of the refrigerators. WARNING: First of all, raise the front feet to reduce the risk of the cabin falling

CONFIDENTIAL 117 You can see previous pages for other installation procedures. 57 8448 0000 / AD

CONFIDENTIAL 11 ALTERNATIVES FOR INSTALLATION The product can be placed in various ways based on the kitchen design. It must be installed at a place

CONFIDENTIAL 12 PREPARATION FOR INSTALLATION The instructions below have been prepared according to Built-in type. Built-in: The Appliance and P

CONFIDENTIAL 13 Location of the Electrical Wiring Location of the electrical wiring must be within the range given below. ATTENTION: Do not use ext

CONFIDENTIAL 14 Location of the Water System The water connected to the water mains must be potable. Location of the water system must be within th

CONFIDENTIAL 15 WARNING:  Flatness of the floor where the product will be installed must be checked with a Bubble Level Tool.  Uprightness of t

CONFIDENTIAL 16 Product Dimensions:

CONFIDENTIAL 17

CONFIDENTIAL 18

CONFIDENTIAL 1 Table of Contents Symbols and Their Meanings ...

CONFIDENTIAL 19 Distances between the furniture doors and the kitchen furniture must be 1/8" (3 mm) minimum.

CONFIDENTIAL 20 Height of the Kitchen Countertop Based on the Min./Max. Height of the Cabin; A B C D Min. 3 3/4" (95 mm) 32 7/16" (824

CONFIDENTIAL 21 Unpacking WARNING: At least two persons must carry the refrigerator.  Use a box cutter to remove the tapes.  Cut the Packaging

CONFIDENTIAL 22  Remove the Packaging Polystyrene material. ATTENTION: Do not remove the tape of the upper door on the product until the refri

CONFIDENTIAL 23 Removing the Connectors on the Side Wall 1 - Side furniture connection bracket closing parts 2 - Seals between the Furniture, Door

CONFIDENTIAL 24 Removing the Mounting Parts in the Freezer Compartment  Open the Freezer Compartment door and remove the Mounting Boxes and docum

CONFIDENTIAL 25 15 - Hanger part screws 16 - Hanger bracket part screws 17 - 90° limiting pins 29 - Cable Clamp 30 - Screw 31 - Furniture Door Prepa

CONFIDENTIAL 26 10 - Position adjustment part 11 - Furniture Connection screws 12 - Freezer Furniture Door Adjustment Washer 13 - Fridge Furniture

CONFIDENTIAL 27 Removing the FRZ Crisper  Remove it manually with 4 knurled screws.  Remove the Lower Crisper.

CONFIDENTIAL 28 Removing the FRZ Door  Remove 2 screws which are near the front section and connect the FRZ Door and the rail.

CONFIDENTIAL 2 INSTALLING THE CABIN BOTTOM ...

CONFIDENTIAL 29  Pull the door frontward to free it from the tabs at the back and remove it. Removing the Lower Vent Hole Assembly  Remove t

CONFIDENTIAL 30 Removing the Upper Vent Hole Part  Remove the 2 screws to take out the Upper Vent Hole Part.

CONFIDENTIAL 31 PRE-INSTALLATION Continue to install the product according to the instructions below. Additionally, consider national and local ins

CONFIDENTIAL 32  Mark the wall for Anti-Tip Brackets (7).  Use a drill to create holes for Dowels (8) at the marked points. (5/16" – Ø8

CONFIDENTIAL 33  Use the hammer to fit the dowels (8).  Fit the brackets (7) into their places, using 4 screws for each. You must use all of

CONFIDENTIAL 34 If there is furniture at the back wall of the refrigerator, please make sure that the furniture is fixed to the wall. For this, you

CONFIDENTIAL 35 Preparing the Water Hose and the Power Plug You will need a hose with a minimum length of 60" (1.5 meters) and a diameter of ¼&

CONFIDENTIAL 36 INSTALLATION TO THE CABIN Taking the Refrigerator from the Wooden Pallet  Remove the 5 brackets that connect the refrigerator

CONFIDENTIAL 37  ove the screws that hold the rear foot of the Wooden Pallet.  Hold the refrigerator firmly, put its weight to the front and p

CONFIDENTIAL 38 ATTENTION: The risk of tipping over is high as of this point. You should not open the doors until the product is placed into the

CONFIDENTIAL 3 Symbols and Their Meanings Symbols used in the installation manual are as follows. Important information or useful usage tips WARNI

CONFIDENTIAL 39  Connect the electrical plug to the socket on the product.  Start the refrigerator and make sure it is energised. (You can chec

CONFIDENTIAL 40 IMPORTANT INFORMATION: You must attach the Freezer Door temporarily to align the product before placing it.

CONFIDENTIAL 41 IMPORTANT INFORMATION: You must use the upper edges of the Freezer Door when aligning the product with the furniture. Adjustment of

CONFIDENTIAL 42 Adjusting the height of the refrigerator in the cabin  Adjust the refrigerator height using the adjustable feet. WARNING: First

CONFIDENTIAL 43  Raise the adjustment part from the cabin's front feet as shown in the figure below to the degree it can get under the cabin

CONFIDENTIAL 44 IMPORTANT INFORMATION: The maximum height that the adjustable feet can reach is 2 1/2" (63 mm) and the product height is 85 3

CONFIDENTIAL 45 IMPORTANT INFORMATION: It is very important to align the upper edge of the Freezer door when aligning. All the other edges can be a

CONFIDENTIAL 46  Position of the level adjustment part (10) must be adjusted according to the thickness of the door. It can adjust the level for

CONFIDENTIAL 47 IMPORTANT INFORMATION: If you have difficulty tightening the screws, opening a reference hole with the drill will make this procedu

CONFIDENTIAL 48 Screwing the upper bracket  Attach the upper bracket to the furniture with 4 screws (11). IMPORTANT INFORMATION: If you have dif

CONFIDENTIAL 4  Minimum clearances between product parts and surrounding structures must be suitable.  Minimum dimensions and proper organisati

CONFIDENTIAL 49 INSTALLING THE CABIN BOTTOM Water connection  Use the box cutter to cut the water hose from the end of the pipe it comes out, leav

CONFIDENTIAL 50 WARNING: This product is suitable for use with cold water mains only. WARNING: Pressure of the water system must be between 25-80

CONFIDENTIAL 51 Attaching the upper vent hole part  Use 2 screws to attach the upper vent hole part.

CONFIDENTIAL 52 Attaching the lower vent hole assembly  Use 2 screws to attach the lower vent hole part. IMPORTANT INFORMATION: You can move t

CONFIDENTIAL 53 WARNING: Forward-backward travel distance of the lower kick plate must be 15/16" (23 mm). As you can see in the figure, the de

CONFIDENTIAL 54 Attaching the kick plate sheet assembly  Remove the paper of the kick plate sheet (5) tapes and attach it by adjusting its ground

CONFIDENTIAL 55 Attaching the decorative parts  Attach the side closing parts (1) onto the right/left connection brackets.  Attach the upper

CONFIDENTIAL 56 FURNITURE DOOR PREPARATION This section contains information about preparing the furniture doors and mounting them to the product.

CONFIDENTIAL 57  You can limit the opening degree of your door to 90° if you want. In this case, the door thickness levels can be like the followi

CONFIDENTIAL 58 Removing the Mechanism Covers  Remove one screw to take out the FF Upper Cover. WARNING: There is a magnet on the FF Upper Cov

CONFIDENTIAL 5 Product weight BRFB1920SS: 486.00 lbs (220.44 Kg) Load bearing capacity of the doors Max. load that the Fridge Door can bear: 55 lbs

CONFIDENTIAL 59 Removing the 3D Adjusting Mechanism on the Refrigerator  Remove the Upper and Lower 3D Adjusting Mechanism Assemblies from the FF

CONFIDENTIAL 60  Remove the 3D Adjusting Mechanism Assembly from the lower part of the FRZ PU Door.  Take out the cradle parts from the mecha

CONFIDENTIAL 61 Preparing the Fridge Furniture Door IMPORTANT INFORMATION: You must take the dimensions into account when grouping the cradle part

CONFIDENTIAL 62 WARNING: Handle connection holes must be adjusted according to the handles to be used in kitchen design. WARNING: Maximum thick

CONFIDENTIAL 63 WARNING: You must use screws suitable for the door thickness.  Install 2 cradles using the chipboard screws (28). You can also us

CONFIDENTIAL 64  Attach the 3D adjusting mechanisms you have removed from the door to the door cradles. The 3D adjusting mechanisms must be attac

CONFIDENTIAL 65 Preparing the Freezer Furniture Door WARNING: Handle connection holes must be adjusted according to the handles to be used in ki

CONFIDENTIAL 66  Install 1 cradle using the chipboard screws (28). You can also use the template (31) provided with the product to align these pa

CONFIDENTIAL 67  Attach the 3D adjusting mechanisms you have removed from the door to the door cradles.  Attach the FRZ door handle. Screws ho

CONFIDENTIAL 68  Use 4 screws to group the freezer inner door on the furniture door as shown in the figure below.

CONFIDENTIAL 6 Product Information: As illustrated in the figure below, you can see the Barcode Level at the top right corner of the FRZ Compartmen

CONFIDENTIAL 69  Attach the brackets to the freezer inner door, using 1 bolt (27) for each bracket and the Crescent Washers (12) specified below.

CONFIDENTIAL 70 Kick Plate Position Adjustment: Nominal distance of the cabin's lower door from the ground is 4" (102 mm). It can be ch

CONFIDENTIAL 71 INSTALLING FURNITURE DOORS Installing the Fridge Furniture Door  Hang the freezer furniture door assembly to the refrigerator usin

CONFIDENTIAL 72  Remove the Upper FF Door fixing bracket screw.  Attach the FF Hanger Bracket (13) part in the mounting box to its place wit

CONFIDENTIAL 73

CONFIDENTIAL 74  Group the FF Upper Mechanism with 4 screws.  Group the Lower Mechanism with 4 screws.

CONFIDENTIAL 75  Remove 2 screws of the hanger part.  Take out the hanger part.

CONFIDENTIAL 76  Remove 2 screws of the Hanger Carrier.  Take out the Hanger Carrier. WARNING: You must keep these parts for future use. Yo

CONFIDENTIAL 77  Fix the Freezer Furniture door assembly onto the rails with 2 screws.

CONFIDENTIAL 78 Adjusting the Furniture Door  WARNING: The product may come with an Inox Door or as Furniture-mountable from the factory. If the

CONFIDENTIAL 7  The ambient temperature must be between 55°F (13°C) and 110°F (43°C). Otherwise, function errors may arise when the product is run

CONFIDENTIAL 79  Remove 4 Fixing Brackets on the fridge door.

CONFIDENTIAL 80  Loosen 3 bracket screws at the upper section of the freezer door. WARNING: These screws should never be removed. Number and dim

CONFIDENTIAL 81  Remove 3 Fixing Brackets at the lower section of the freezer door.  Position of the Furniture Doors to the kitchen furnitur

CONFIDENTIAL 82

CONFIDENTIAL 83  Adjust the Furniture Doors with the 3D adjusting mechanism. You can adjust furniture doors with the 3-axis screw mechanism. Oper

CONFIDENTIAL 84

CONFIDENTIAL 85  After completing door adjustments, attach the brackets to the middle section of the Fridge door.

CONFIDENTIAL 86  Attach additional brackets to the upper and lower sections of the Fridge Furniture Door's handle part.

CONFIDENTIAL 87  Tighten the screws together with enough Crescent Washers to cover the clearance under the upper brackets of the Freezer Door.

CONFIDENTIAL 88  Attach the lower-middle bracket of the Freezer Door.  Attach the lower side brackets of the Freezer Door.

CONFIDENTIAL 8 The appliance is provided with a NEMA 5-15 P plug and a 3-pin power cable which is in the UL list and ready to be connected to a 120

CONFIDENTIAL 89 Attaching the covers  Attach and screw the Upper Cover of the Fridge Door.  Attach and screw the Lower Door of the Fridge Doo

CONFIDENTIAL 90  Attach the FRZ Cover (6) using the tabs.  Attach the side closing seals (2) (3).

CONFIDENTIAL 91 HINGE ADJUSTMENT Adjusting the hardness of the hinges  Use a drill to adjust the hardness of the upper and lower hinges of the FF

CONFIDENTIAL 92 WARNING: This adjustment must definitely be performed after the door has been adjusted.

CONFIDENTIAL 93 CHANGING THE DIRECTION OF THE FF DOOR Removing the FF clad door  Set the hardness level of the hinge to "0". ATTENTION

CONFIDENTIAL 94  Loosen one screw of the Upper Cover of the Fridge Door and remove it.  Loosen one screw of the Lower Cover of the Fridge Doo

CONFIDENTIAL 95  Remove FF Lower and Upper Bracket screws.  Remove the screw of FF Upper and Lower mechanisms. WARNING: The clad door will be

CONFIDENTIAL 96  Take the Fridge Furniture Door and lay it down on a table upside down. You must attach the Furniture Door by rotating it 180°

CONFIDENTIAL 97 Removing and preparing the Fridge Inner Door  Remove the hinge connection screws of the Hinge Brackets. ATTENTION: The clad do

CONFIDENTIAL 98  Take out the FF Door and lay it down on a table.  Remove the Upper Hinge brackets on the FF Door and screw them to the other