Blomberg DWT81900FBI Instrukcja i Przewodnik Użytkownika

www.blomberginternational.cominfo@blomberginternational.comDishwasherInstallation ManualDWT 52600 SSIHDWT 52600 BIHDWT 52800 WIHDWT 52800 SSIHDWT 8190

7USA?d)

8USA(+50mm)j+ 50max 50Place the two mounting brackets into the top corners of the dishwasher.Fix the mounting brackets (A) to the top corners of the d

9USA6.3 ADJUSTING HEIGHTIf the height of the enclosure is 337/8” to 357/8” (861 mm - 911mm) adjust supports as shown in the gure.Supplied (4)Adjust t

10USA6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solder connections

11USA NOTICE :• Either one of the above methods must be used or the dishwasher will not operate properly.• A hose that attaches to a sink spray can

12USA6.7 STEAM PROTECTION FOILSteam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it

13USA7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses and electrical connection

14USA7.1.2 WATER SUPPLY CONNECTIONWater supply may be connected to the dishwasher in one of two ways:• With metal braided hose.• With copper tubing.

15USA7.3 ADJUSTING THE MOVABLE TOE KICKNow that you have successfully installed the dishwasher, you need to attach the toe kick to the dishwasher. The

16USAOpen the xing part on the Toe Kick(p). (A)Place it on the slots, which are on the brackets xed before, and adjust the height (max. 40 mm). (B)C

DishwasherInstallation ManualDWT 52600 SSIHDWT 52600 BIHDWT 52800 WIHDWT 52800 SSIHDWT 81900 FBIDWT 51600 WDWT 81900 SSDW 51600 SSDW 51600 FBIDWT 5160

17USA7.4 FIXING THE CABINET TO THE COUNTER(y)TALL TUB MODELSSTANDART TUB MODELS

18USA7.5 PREPARING THE TIMBER DOORX = ?X==Mid. Point==Mid. PointHeight (h) : Height of the wooden door 30” (760mm) Tall Tub Models OnlyHeight (h) :

19USA127.6 PREPARING THE PRODUCT DOOR(t)

20USA123412345123457.9 INSTALLING THE TIMBER DOOR7.10 FIXING THE TIMBER DOOR

21USA7.11 FIXING THE TIMBER DOOR7.12 ADJUSTING THE KICK PLATE• Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A).•

22USAmin 300~ 1500~ 1800~ 2000min 500max 1000max 10001234c12121243min300min120max 1000min 5007.13 CONNECTION

23USA8. INSTALLER CHECKLISTYour installer must have completed and checked the following:• The dishwasher is square and level.• The dishwasher is fas

[email protected]

INTRODUCTION 11. IMPORTANT SAFETY INSTRUCTIONS 11.1 INSPECT THE DISHWASHER 22. TOOLS WHICH MAY BE NEEDED 33. MATERIALS WHICH MAY BE NEEDED 34. MAT

1USAINTRODUCTIONPlease read this installation manual and particularly the safety instructions completely and carefully. They will save you time and ef

2USAdesigned for an electrical supply of 120 V (volts), 60 Hz (hertz), AC, connected to a dishwasher-dedicated, properly grounded electrical circuit w

3USA2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line

4USA4. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you h

5USA5. DISHWASHER SPECIFICATIONS5.1 TECHNICAL FEATURESLoad capacity 14 place settingsPermissible water pressure 4.35 - 145 psi (0.3 - 10 bars) Electri

6USA6. ENCLOSURE PREPARATION6.1 ELECTRICAL PREPARATION WARNINGThe dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a